product name

Troy-Bilt 2215-2228 Horse III Horse

Model: 511878

Back To Assemblies

Save
 Part Not Listed?Part Not Listed?
product name

Wheel Speed Lever, Belt Drive System, Engines, Wheels

...
...
1
PIN - spring, 1/8" dia., retains castle nut to threaded stud MTD-GW-9362
...
2
NUT-castle (slotted), 1/2"-20. MTD-GW-9838
...
3
WASHER- shoulder, 1/2" (shoulder faces disc washers) MTD-GW-9934
...
4
WASHER- disc spring (concave surfaces face each other) MTD-GW-9932
...
5
LEVER - wheel speed shift Includes #2244 knob (Ref. #8) and 199120 retaining ring (Ref. #18) MTD-GW-2628
...
6
KNOB - wheel speed shift lever Includes #9120 retaining ring (Ref. 1118) and plastic decal inlay MTD-1902240
...
7
PIN - cotter, 3/32" x 1" MTD-GW-9317
...
8
ROD - connecting rod, wheel speed shift lever MTD-GW-1231
...
9
SWIVEL - connecting rod MTD-GW-1033
...
10
WASHER - flat, 5/16",S.A.E. MTD-736-0567
...
11
PIN - hair cotter MTD-714-04048
...
12
LOCKNUT-hex. hd., 5/16"-18, retains swivel to eccentric lever MTD-NA
...
13
BOLT - hex. hd., 3/8"-16 x 1" MTD-710-0514
...
14
L-Wash. 3/8" I.D. MTD-736-0169
...
15
WASHER - flat, 3/8", S.A.E. MTD-736-3050
...
16
BUSHING - spacer, 21/64" (.325") long, yoke to engine mount MTD-GW-2146
...
17
BUSHING - spacer, 19/64" (.300") long, yoke link to retaining plug MTD-GW-1113-1099
...
18
RING - retaining (tolerance ring) MTD-GW-9120
...
19
BLOCK - belt adjustment, 3-7/8" long Includes mounting hardware and belt adjustment rod (Ref. #'s 13,14,15, & 20 MTD-GW-1920
...
20
ROD - belt adjustment, 7" long, with measuring gauge MTD-GW-2100
...
21
Screw, 3/8-24 x 1.75 MTD-710-0539
...
22
BOLT - hex. hd., 3/8"-24 x 1-1/2", engine pulley For Kohler and Briggs & Stratton Engines MTD-710-0459A
...
23
DISC-reverse, rubber rimmed Includes #1920 belt adjustment block (Ref.#19) MTD-GW-1919
...
23
DISC ONLY-reverse, rubber rimmed MTD-756-04171
...
24
BELT -forward drive MTD-GW-9245
...
25
PULLEY- engine P.T.O. (Power Take Off) MTD-619-04124
...
26
SHIM - engine pulley, 1/16" thick MTD-736-04187
...
26
SHIM - same as above, 1/32" thick MTD-736-04192
...
27
KEY - engine pulley, 3/16" square x 2-1/2" MTD-GW-9303
...
28
BOLT -hex. hd., 5/16"-18 x 1", Grades. Retains engine mounting bar ENGINES AND ENGINE MOUNT MTD-710-0376
...
29
HEX NUT 5/16-18 ENGINES AND ENGINE MOUNT MTD-712-3010
...
30
BAR- engine mounting ENGINES AND ENGINE MOUNT MTD-GW-1034A
...
31
PLUG - thread protector, red plastic ENGINES AND ENGINE MOUNT MTD-GW-9147
...
32
BOLT- hex. hd., 5/16"-24 x 1-1/8", engine mounting ENGINES AND ENGINE MOUNT MTD-710-0672
...
33
LOCKWASHER-springlock, 5/16" ENGINES AND ENGINE MOUNT MTD-936-0119
...
34
MOUNT- engine to tiller Includes four #9572 mounting bolts (Ref.#32); ; ENGINES AND ENGINE MOUNT MTD-GW-1968
...
35
TECUMSEH ENGINE - 6 HP, recoil start, Model HH60, Specification 105126J, solid state electronic ignition, horizontal crankshaft is turned down to 3/4" at PTO end to accept engine pulley; ENGINES AND ENGINE MOUNT MTD-NA
...
35
TECUMSEH ENGINE - 6 HP, electric start, Model HH-60, Specification 105127J Same as Part No. 10226 engine, but with electric start.; ENGINES AND ENGINE MOUNT MTD-NA
...
35
7 HP TECUMSEH ENGINE-Recoil start Model #HMXL700.132501; ENGINES AND ENGINE MOUNT MTD-NA
...
35
7 HP TECUMSEH ENGINE-Electric start Model #HMXL70-132502; ENGINES AND ENGINE MOUNT MTD-NA
...
35
KOHLER ENGINE-8 HP Magnum, recoil start Model M8T, Specification P5.301512, solid state electronic ignition, horizontal crankshaft is turned down to 3/4" at PTO end to accept engine pulley; ENGINES AND ENGINE MOUNT MTD-NA
...
35
KOHLER ENGINE - 8 HP Magnum, electric start Model MBS, Specification PS-301513. Same as Part No. 10203 engine, but with electric start. For use with tillers already equipped with Key Switch Starting System (GRID D-13); ENGINES AND ENGINE MOUNT MTD-NA
...
36
PIN -roll (spirol, 5/16" x 1-1/2" long, wheel hub to shaft WHEEL & TIRE ASSEMBLIES MTD-GW-9322099
...
37
WHEEL & TIRE ASSEMBLY - standard tread, LEFT SIDE 4:00/4:80 x 8" tubeless tire with valve stem, mounted on single-piece steel wheel. No Longer Available MTD-GW-9142
...
38
WHEEL & TIRE ASSEMBLY - bar tread, LEFT SIDE 4:80 x 8" tubeless tire with valve stem, mounted on single-piece steel wheel. No Longer Available MTD-GW-9143
...
38A
WHEEL & TIRE ASSEMBLY - bar tread, RIGHT SIDE. No Longer Available Same as #9143 but for right side of tiller; WHEEL & TIRE ASSEMBLIES MTD-GW-9144
...
39
CAP - wheel hub WHEEL & TIRE ASSEMBLIES MTD-1902020
...
...
...
Processing